Kategorijos

Weber - savaime išsilyginantis grindų sluoksnis Grindys 4150

gamintojas: Weber - Maxit

kategorija: WEBER - statybinės cheminės medžiagos

Produkto Nr.: 22471

Užsakyto numerio kartotinis: 42 Įdėti į krepšelį

Pridėti į mainų sritį Klauskite produkto Praneškite apie klaidą apraše Įsigyti išsimokėtinai galima nuo 100 PLN produkto vertės arba viso užsakymo. Lizingą galima įsigyti nuo 369 PLN produkto vertės

kaina pagal užklausimą

kainoraščio kaina
vieneto grynasis
21.43EUR
vnt
reklaminė kaina
vieneto grynasis
13.63EUR
vnt
minimalus komercinis
produkto kiekis
1.00 vnt
vienetas
prekyba
1.00 vnt
visos kainos
grynasis kainoraštis
21.43EUR
1.00 vnt
visos kainos
reklaminis tinklas
13.63EUR
1.00 vnt
kainoraščio kaina
bruto vienetas
26.36EUR
vnt
reklaminė kaina
bruto vienetas
16.76EUR
vnt
minimalus komercinis
produkto kiekis
1.00 vnt
vienetas
prekyba
1.00 vnt
visos kainos
kainoraštis bruto
26.36EUR
1.00 vnt
visos kainos
reklaminė bruto
16.76EUR
1.00 vnt

Produkto aprašymas

Cement floor self-leveling underlayment, in the form of a dry mix, ready to use after mixing with water. Product in accordance with PN-EN 13813; polymer modified; CT-C25-F5

Application

  • For fast execution of the substrate, very smooth and leveled undercoat with thin and thick carpets, PVC, cork, linoleum, ceramic and stone tiles, parquet (flexible adhesives recommended), panels etc.
  • weber.floor 4150 for machine application allows very fast execution of precisely leveled undercoat on large surfaces (capacity approx. 400 m per hour).
  • For use inside buildings in apartments, hotels, offices, hospitals, schools, shops, cinemas, etc. public facilities, on concrete substrates and cement screeds.

Weber.floor 4150 is not recommended to be used without the above-mentioned topcoats.

Substrate preparation

The substrate must be load-bearing, hard, stable, dry and free from impurities that weaken the bond (e.g. grease, bitumen, dust, glues, adhesives, paint and mortar residues). The tensile strength of the substrate should be at least 1.0 N / mm. Seal openings in the ceiling to prevent mortar from leaking. Prime larger defects (> 30 mm) with weber.floor 4716 - concentrate for dilution with water or weber PG201 - ready to use (soil to dry) and fill with weber.floor RAPID, weber.floor 6000 or weber.floor 4040 Vacuum and prime the ground thoroughly with weber.floor 4716 or weber PG201.

Priming weber.floor 4716 (pour the preparation into water):

  • concrete substrates - concentrate mixed with water in a 1: 3 ratio (soil: water),
  • absorbent substrates (e.g. porous concrete, cement screeds) - first priming 1: 5, second 1: 3.

Priming weber PG201 (mix the contents of the packaging before use):

  • prime concrete substrates without thinning,
  • absorbent substrates: prime twice - first with diluted 2: 1 diluted soil, second - without dilution.

Pour the prepared primer onto the ground and spread evenly with a soft brush. It is unacceptable to leave excess primer in the cavities. Leave the primer to dry (approx. 3-5 hours). The priming layer increases the adhesion of the mortar to the substrate, facilitates its leveling, prevents the formation of air bubbles and dehydration of the mortar before setting. Detailed information on priming is included in the technical sheets of the primer. Make circumferential expansion joints around walls, columns, pipes etc. using e.g. weber.floor 4960 expansion tape.


priedai